APRS Track Direct

My position About ☰

reset

TA5AQD-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA5AQD-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1758199976	23 Pkt	31 dBm	12 V
1758196188	44 Pkt	31 dBm	12 V
1758195250	32 Pkt	31 dBm	12 V
1758193410	22 Pkt	31 dBm	12 V
1758192450	29 Pkt	31 dBm	12 V
1758191543	35 Pkt	31 dBm	12 V
1758190585	56 Pkt	31 dBm	12 V
1758186839	44 Pkt	31 dBm	12 V
1758185977	57 Pkt	31 dBm	12 V
1758183163	36 Pkt	31 dBm	12 V
1758181230	40 Pkt	31 dBm	12 V
1758180616	44 Pkt	31 dBm	12 V
1758177496	39 Pkt	31 dBm	12 V
1758166283	27 Pkt	31 dBm	12 V
1758162574	30 Pkt	31 dBm	12 V
1758161606	23 Pkt	31 dBm	12 V
1758160673	29 Pkt	31 dBm	12 V
1758159738	31 Pkt	31 dBm	12 V
1758158803	28 Pkt	31 dBm	12 V
1758157867	32 Pkt	31 dBm	12 V
1758156931	28 Pkt	31 dBm	12 V
1758152261	35 Pkt	31 dBm	12 V
1758149459	22 Pkt	31 dBm	12 V
1758143855	29 Pkt	31 dBm	12 V
1758142920	26 Pkt	31 dBm	12 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)