APRS Track Direct

My position About ☰

reset

BV2FP-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV2FP-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1836274571	29.2 C	2 p	2 p	73 p	1205 p
1770460337	12.5 C	50 p	59 p	84 p	84 p
1770459137	12 C	50 p	59 p	84 p	84 p
1770457937	13.4 C	50 p	59 p	84 p	84 p
1770456738	12.8 C	50 p	59 p	84 p	84 p
1770455537	14.3 C	50 p	59 p	84 p	84 p
1770454339	13.2 C	27 p	27 p	52 p	51 p
1770453137	13.4 C	18 p	25 p	25 p	25 p
1770451938	14.3 C	18 p	25 p	25 p	25 p
1770450738	13.9 C	18 p	25 p	25 p	25 p
1770449537	13.7 C	18 p	25 p	25 p	25 p
1770448337	13.4 C	7 p	7 p	7 p	7 p
1770447137	14.4 C	3 p	3 p	3 p	3 p
1770445938	14.7 C	2 p	2 p	3 p	4912 p
1770444737	14.3 C	2 p	2 p	3 p	4912 p
1770443537	13.8 C	2 p	2 p	3 p	4912 p
1770442337	14.8 C	2 p	2 p	3 p	4912 p
1770441137	13.7 C	2 p	2 p	3 p	4912 p
1770439937	14.2 C	2 p	2 p	3 p	4912 p
1770438737	12.8 C	2 p	2 p	3 p	4912 p
1770437538	15.1 C	2 p	2 p	3 p	4912 p
1770436337	13.8 C	2 p	2 p	3 p	4912 p
1770435137	13 C	2 p	2 p	3 p	4912 p
1770433937	10.8 C	2 p	2 p	3 p	4912 p
1770426573	14.9 C	2 p	2 p	3 p	4912 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)