APRS Track Direct

My position About ☰

reset

K8GPS-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K8GPS-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Temp*	Rx1h*	Dg1h*
1753514148	12.38 Volt	33 C	1130 Pkt	250 Pkt
1753514143	12.38 Volt	33 C	1130 Pkt	250 Pkt
1753513843	12.38 Volt	33 C	1160 Pkt	250 Pkt
1753513547	12.38 Volt	33 C	1160 Pkt	250 Pkt
1753513543	12.38 Volt	33 C	1160 Pkt	250 Pkt
1753513243	12.38 Volt	33 C	1190 Pkt	250 Pkt
1753512945	12.38 Volt	33 C	1190 Pkt	250 Pkt
1753512943	12.38 Volt	33 C	1190 Pkt	250 Pkt
1753512643	12.38 Volt	33 C	1200 Pkt	250 Pkt
1753512346	12.38 Volt	33 C	1210 Pkt	250 Pkt
1753512343	12.38 Volt	33 C	1210 Pkt	250 Pkt
1753512043	12.38 Volt	33 C	1240 Pkt	250 Pkt
1753511744	12.38 Volt	33 C	1230 Pkt	250 Pkt
1753511743	12.38 Volt	33 C	1230 Pkt	250 Pkt
1753511443	12.38 Volt	33 C	1250 Pkt	260 Pkt
1753511144	12.38 Volt	33 C	1250 Pkt	250 Pkt
1753511143	12.38 Volt	33 C	1250 Pkt	250 Pkt
1753510843	12.38 Volt	33 C	1240 Pkt	250 Pkt
1753510551	12.3 Volt	33 C	1210 Pkt	250 Pkt
1753510543	12.3 Volt	33 C	1210 Pkt	250 Pkt
1753510243	12.38 Volt	33 C	1210 Pkt	240 Pkt
1753509944	12.38 Volt	33 C	1200 Pkt	240 Pkt
1753509943	12.38 Volt	33 C	1200 Pkt	240 Pkt
1753509643	12.38 Volt	33 C	1210 Pkt	240 Pkt
1753509352	12.38 Volt	33 C	1210 Pkt	240 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)