APRS Track Direct

My position About ☰

reset

BX2AMP-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX2AMP-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1758228615	36.3 C	2 p	7 p	1259 p
1758227415	37.8 C	2 p	8 p	1260 p
1758226215	37.1 C	3 p	10 p	1262 p
1758225015	36.3 C	3 p	10 p	1262 p
1758223816	37.2 C	4 p	10 p	1262 p
1758222615	37.3 C	3 p	10 p	1260 p
1758221415	37.2 C	3 p	10 p	1260 p
1758220215	37.7 C	4 p	10 p	1260 p
1758219015	37.8 C	3 p	10 p	1260 p
1758217815	37.7 C	3 p	10 p	1260 p
1758216615	37.3 C	4 p	10 p	1260 p
1758215415	37.8 C	3 p	10 p	1260 p
1758214215	37.9 C	3 p	10 p	1260 p
1758213016	38.5 C	4 p	10 p	1260 p
1758211815	38.8 C	3 p	13 p	1260 p
1758210615	38.6 C	3 p	13 p	1260 p
1758209415	39.4 C	7 p	13 p	1260 p
1758208216	39.1 C	3 p	10 p	1260 p
1758207015	38.8 C	3 p	10 p	1260 p
1758205815	39.2 C	4 p	10 p	1260 p
1758204615	39.1 C	3 p	10 p	1260 p
1758203415	39.4 C	3 p	12 p	1260 p
1758202216	40.3 C	4 p	61 p	1260 p
1758201016	40.8 C	5 p	104 p	1260 p
1758199815	41.2 C	52 p	139 p	1258 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)