APRS Track Direct

My position About ☰

reset

IQ3TS-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IQ3TS-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Volt*
1836274772	92 Pkt	610 Pkt	14.38 Volt
1836274472	96 Pkt	620 Pkt	14.38 Volt
1836274322	81 Pkt	590 Pkt	14.38 Volt
1836274172	90 Pkt	630 Pkt	14.38 Volt
1836273872	82 Pkt	620 Pkt	14.38 Volt
1778017595	54 Pkt	360 Pkt	14.38 Volt
1778017295	55 Pkt	370 Pkt	14.3 Volt
1778016995	66 Pkt	380 Pkt	14.38 Volt
1778016695	60 Pkt	390 Pkt	14.38 Volt
1778016395	45 Pkt	390 Pkt	14.3 Volt
1778016095	47 Pkt	390 Pkt	14.3 Volt
1778015795	45 Pkt	400 Pkt	14.38 Volt
1778015495	60 Pkt	400 Pkt	14.38 Volt
1778015195	68 Pkt	390 Pkt	14.38 Volt
1778014895	54 Pkt	390 Pkt	14.3 Volt
1778014595	52 Pkt	390 Pkt	14.38 Volt
1778014295	58 Pkt	390 Pkt	14.38 Volt
1778014003	73 Pkt	390 Pkt	14.38 Volt
1778013695	68 Pkt	390 Pkt	14.3 Volt
1778013395	68 Pkt	370 Pkt	14.38 Volt
1778013095	55 Pkt	370 Pkt	14.38 Volt
1778012795	52 Pkt	360 Pkt	14.38 Volt
1778012495	66 Pkt	370 Pkt	14.38 Volt
1778012195	47 Pkt	360 Pkt	14.38 Volt
1778011895	58 Pkt	360 Pkt	14.38 Volt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

DgR: 0, 0.001, 0

Volt: 0, 0.079, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)