APRS Track Direct

My position About ☰

reset

YO3FVR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YO3FVR-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Tin*
1770124894	0 Volt	75 Pcnt	5.5 C
1770124294	13.35 Volt	62 Pcnt	5.5 C
1770123694	14.03 Volt	66 Pcnt	5.5 C
1770123094	0 Volt	47 Pcnt	5.5 C
1770122494	0 Volt	40 Pcnt	5.5 C
1770121894	0 Volt	45 Pcnt	5.5 C
1770121294	0.15 Volt	52 Pcnt	5 C
1770120694	0 Volt	47 Pcnt	5 C
1770120094	0 Volt	51 Pcnt	5 C
1770119494	8.85 Volt	52 Pcnt	5 C
1770118894	14.78 Volt	60 Pcnt	5 C
1770118294	0.08 Volt	63 Pcnt	5 C
1770117694	2.03 Volt	74 Pcnt	4.5 C
1770117094	0 Volt	72 Pcnt	4.5 C
1770116494	0 Volt	55 Pcnt	4.5 C
1770115894	0 Volt	61 Pcnt	4.5 C
1770115294	7.95 Volt	58 Pcnt	4.5 C
1770114694	0 Volt	50 Pcnt	4.5 C
1770114094	0 Volt	38 Pcnt	4 C
1770113494	0 Volt	51 Pcnt	4 C
1770112894	17.33 Volt	63 Pcnt	4 C
1770112294	8.25 Volt	59 Pcnt	3.5 C
1770111694	17.4 Volt	53 Pcnt	3.5 C
1770111094	0 Volt	57 Pcnt	3.5 C
1770110494	0 Volt	60 Pcnt	3 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Vsol: 0, 0.075, 0

Isol: 0, 0.1, 0

Eff1h: 0, 1, 0

Tin: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)