APRS Track Direct

My position About ☰

reset

YM5KSN Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM5KSN. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1754121717	6 Pkt	-58 dBm	5.76 V
1754121436	20 Pkt	-60 dBm	5.76 V
1754121093	7 Pkt	-57 dBm	5.76 V
1754120780	14 Pkt	-58 dBm	5.76 V
1754120443	12 Pkt	-59 dBm	5.78 V
1754120107	9 Pkt	-57 dBm	5.76 V
1754119794	13 Pkt	-63 dBm	5.76 V
1754119458	9 Pkt	-58 dBm	5.76 V
1754119125	14 Pkt	-59 dBm	5.76 V
1754118575	97 Pkt	-58 dBm	5.76 V
1754118152	24 Pkt	-60 dBm	5.76 V
1754117832	102 Pkt	-60 dBm	5.76 V
1754117406	25 Pkt	-58 dBm	5.76 V
1754117235	105 Pkt	-61 dBm	5.76 V
1754116803	78 Pkt	-59 dBm	5.76 V
1754116403	6 Pkt	-59 dBm	5.76 V
1754116222	17 Pkt	-60 dBm	5.76 V
1754115884	18 Pkt	-62 dBm	5.76 V
1754115541	7 Pkt	-60 dBm	5.76 V
1754115333	22 Pkt	-59 dBm	5.76 V
1754114986	93 Pkt	-60 dBm	5.78 V
1754114569	20 Pkt	-59 dBm	5.76 V
1754114247	99 Pkt	-61 dBm	5.76 V
1754113658	24 Pkt	-60 dBm	5.74 V
1754113213	55 Pkt	-60 dBm	5.76 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)