APRS Track Direct

My position About ☰

reset

E27EKO-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E27EKO-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1750179462	1 Pkt	-73 dBm	4.86 V
1750178840	0 Pkt	-71 dBm	4.88 V
1750178218	0 Pkt	-73 dBm	4.86 V
1750177596	0 Pkt	-72 dBm	4.86 V
1750176974	1 Pkt	-73 dBm	4.86 V
1750176354	0 Pkt	-72 dBm	4.86 V
1750175731	0 Pkt	-73 dBm	4.86 V
1750175109	0 Pkt	-73 dBm	4.86 V
1750174500	0 Pkt	-74 dBm	4.86 V
1750173865	0 Pkt	-72 dBm	4.86 V
1750173242	0 Pkt	-72 dBm	4.86 V
1750172620	1 Pkt	-74 dBm	4.86 V
1750171998	0 Pkt	-71 dBm	4.86 V
1750171376	0 Pkt	-72 dBm	4.86 V
1750170754	0 Pkt	-73 dBm	4.86 V
1750170134	0 Pkt	-73 dBm	4.88 V
1750169510	1 Pkt	-74 dBm	4.86 V
1750168890	0 Pkt	-72 dBm	4.86 V
1750168266	0 Pkt	-74 dBm	4.86 V
1750167644	1 Pkt	-74 dBm	4.86 V
1750167022	0 Pkt	-73 dBm	4.86 V
1750166400	0 Pkt	-72 dBm	4.86 V
1750165778	0 Pkt	-72 dBm	4.86 V
1750165156	0 Pkt	-73 dBm	4.86 V
1750164534	0 Pkt	-74 dBm	4.86 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)