APRS Track Direct

My position About ☰

reset

OE3PDB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3PDB-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1782504798	10.35 Volt	150 Pkt	70 Pkt	52 Pcnt
1782501195	10.35 Volt	160 Pkt	80 Pkt	57 Pcnt
1782497591	10.35 Volt	160 Pkt	80 Pkt	51 Pcnt
1782493988	10.35 Volt	160 Pkt	70 Pkt	53 Pcnt
1782490385	10.35 Volt	210 Pkt	100 Pkt	54 Pcnt
1782486781	10.35 Volt	270 Pkt	110 Pkt	53 Pcnt
1782483178	10.35 Volt	240 Pkt	100 Pkt	56 Pcnt
1782479574	10.35 Volt	200 Pkt	100 Pkt	58 Pcnt
1782475971	10.35 Volt	210 Pkt	90 Pkt	55 Pcnt
1782472367	10.35 Volt	160 Pkt	80 Pkt	49 Pcnt
1782468764	10.35 Volt	180 Pkt	80 Pkt	53 Pcnt
1782465161	10.35 Volt	210 Pkt	90 Pkt	61 Pcnt
1782461557	10.35 Volt	250 Pkt	100 Pkt	52 Pcnt
1782457954	10.35 Volt	260 Pkt	100 Pkt	57 Pcnt
1782454350	10.35 Volt	240 Pkt	100 Pkt	54 Pcnt
1782450747	10.35 Volt	210 Pkt	100 Pkt	53 Pcnt
1782447143	10.35 Volt	230 Pkt	90 Pkt	52 Pcnt
1782443540	10.35 Volt	190 Pkt	70 Pkt	47 Pcnt
1782439936	10.35 Volt	200 Pkt	90 Pkt	52 Pcnt
1782436333	10.35 Volt	180 Pkt	80 Pkt	55 Pcnt
1782432730	10.35 Volt	180 Pkt	80 Pkt	47 Pcnt
1782429126	10.35 Volt	190 Pkt	80 Pkt	55 Pcnt
1782425524	10.35 Volt	180 Pkt	90 Pkt	58 Pcnt
1782421919	10.35 Volt	240 Pkt	140 Pkt	56 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)