APRS Track Direct

My position About ☰

reset

PT7RF-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object PT7RF-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1774493035	1 Pkt	-50 dBm	6.67 V
1774492111	1 Pkt	-52 dBm	6.73 V
1774491187	1 Pkt	-49 dBm	6.75 V
1774490263	1 Pkt	-49 dBm	6.56 V
1774489339	1 Pkt	-50 dBm	6.71 V
1774488415	1 Pkt	-50 dBm	6.56 V
1774487491	0 Pkt	-48 dBm	6.71 V
1774487155	1 Pkt	-51 dBm	6.71 V
1774486231	2 Pkt	-52 dBm	6.4 V
1774485306	1 Pkt	-50 dBm	6.58 V
1774484382	1 Pkt	-50 dBm	6.48 V
1774483457	1 Pkt	-50 dBm	6.56 V
1774482533	1 Pkt	-51 dBm	6.54 V
1774481608	1 Pkt	-51 dBm	6.54 V
1774480684	1 Pkt	-49 dBm	6.5 V
1774479760	1 Pkt	-48 dBm	6.56 V
1774478836	1 Pkt	-50 dBm	6.71 V
1774477912	1 Pkt	-50 dBm	6.56 V
1774476988	1 Pkt	-50 dBm	6.69 V
1774476064	1 Pkt	-49 dBm	6.77 V
1774475140	1 Pkt	-50 dBm	6.54 V
1774474217	0 Pkt	-50 dBm	6.5 V
1774473219	1 Pkt	-49 dBm	6.58 V
1774472295	1 Pkt	-50 dBm	6.71 V
1774471371	1 Pkt	-50 dBm	6.77 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)