APRS Track Direct

My position About ☰

reset

TA3KT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA3KT-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1750145778	0 Pkt	-80 dBm	0.16 V
1750145048	0 Pkt	-81 dBm	0.16 V
1750144318	0 Pkt	-79 dBm	0.16 V
1750143588	0 Pkt	-80 dBm	0.16 V
1750142858	0 Pkt	-78 dBm	0.16 V
1750142128	0 Pkt	-77 dBm	0.16 V
1750141398	0 Pkt	-75 dBm	0.16 V
1750140668	0 Pkt	-76 dBm	0.16 V
1750139938	0 Pkt	-75 dBm	0.16 V
1750139208	0 Pkt	-76 dBm	0.16 V
1750138478	0 Pkt	-74 dBm	0.16 V
1750137748	0 Pkt	-75 dBm	0.16 V
1750137018	0 Pkt	-73 dBm	0.16 V
1750136288	0 Pkt	-73 dBm	0.16 V
1750135558	0 Pkt	-76 dBm	0.16 V
1750134828	0 Pkt	-78 dBm	0.16 V
1750134098	0 Pkt	-78 dBm	0.16 V
1750133368	0 Pkt	-78 dBm	0.16 V
1750132638	0 Pkt	-78 dBm	0.16 V
1750131908	0 Pkt	-78 dBm	0.16 V
1750131178	0 Pkt	-79 dBm	0.16 V
1750130448	0 Pkt	-77 dBm	0.16 V
1750129644	0 Pkt	-80 dBm	0.14 V
1750128914	0 Pkt	-78 dBm	0.16 V
1750128184	2 Pkt	-77 dBm	0.16 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)