This is the latest recevied telemetry packets stored in our database for station/object TLGRPH. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | V_Batt* | V_Ext* | RX_rate* | RelRate* | DrpRate* |
|---|---|---|---|---|---|
| 1794918766 | 4.13 VDC | 13 VDC | 168 pkt/h | 88 pkt/h | 80 pkt/h |
| 1794917866 | 4.13 VDC | 13 VDC | 188 pkt/h | 92 pkt/h | 96 pkt/h |
| 1794916966 | 4.13 VDC | 13 VDC | 212 pkt/h | 96 pkt/h | 116 pkt/h |
| 1794916066 | 4.13 VDC | 13 VDC | 160 pkt/h | 72 pkt/h | 88 pkt/h |
| 1794915165 | 4.13 VDC | 13 VDC | 180 pkt/h | 84 pkt/h | 96 pkt/h |
| 1794914265 | 4.13 VDC | 13 VDC | 112 pkt/h | 64 pkt/h | 48 pkt/h |
| 1794913365 | 4.14 VDC | 13 VDC | 164 pkt/h | 92 pkt/h | 72 pkt/h |
| 1794911565 | 4.13 VDC | 13 VDC | 188 pkt/h | 92 pkt/h | 96 pkt/h |
| 1794910664 | 4.13 VDC | 13 VDC | 168 pkt/h | 80 pkt/h | 88 pkt/h |
| 1794909764 | 4.13 VDC | 13 VDC | 160 pkt/h | 88 pkt/h | 72 pkt/h |
| 1794908864 | 4.13 VDC | 13 VDC | 136 pkt/h | 76 pkt/h | 60 pkt/h |
| 1794907964 | 4.13 VDC | 13 VDC | 180 pkt/h | 96 pkt/h | 84 pkt/h |
| 1794907063 | 4.13 VDC | 13 VDC | 160 pkt/h | 76 pkt/h | 84 pkt/h |
| 1794906163 | 4.13 VDC | 13 VDC | 142 pkt/h | 91 pkt/h | 51 pkt/h |
*Used Equation Coefficients:
V_Batt: 0, 0.01, 0
V_Ext: 0, 0.02, 0
RX_rate: 0, 1, 0
RelRate: 0, 1, 0
DrpRate: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)