APRS Track Direct

My position About ☰

reset

OK1RPL-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OK1RPL-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Rx1h*	Dg1h*	Eff1h*
1732295713	270 Pkt	100 Pkt	85 Pcnt
1732294812	320 Pkt	130 Pkt	85 Pcnt
1732293912	350 Pkt	150 Pkt	85 Pcnt
1732293011	360 Pkt	150 Pkt	84 Pcnt
1732292110	380 Pkt	160 Pkt	85 Pcnt
1732291209	360 Pkt	140 Pkt	88 Pcnt
1732290308	340 Pkt	130 Pkt	85 Pcnt
1732289407	350 Pkt	130 Pkt	87 Pcnt
1732288506	340 Pkt	130 Pkt	86 Pcnt
1732287605	350 Pkt	140 Pkt	85 Pcnt
1732286705	350 Pkt	140 Pkt	87 Pcnt
1732285804	350 Pkt	150 Pkt	87 Pcnt
1732284903	360 Pkt	150 Pkt	86 Pcnt
1732284002	360 Pkt	150 Pkt	87 Pcnt
1732283101	390 Pkt	150 Pkt	87 Pcnt
1732282200	390 Pkt	150 Pkt	86 Pcnt
1732281299	410 Pkt	160 Pkt	87 Pcnt
1732280399	430 Pkt	170 Pkt	87 Pcnt
1732279498	430 Pkt	170 Pkt	87 Pcnt
1732278597	420 Pkt	170 Pkt	87 Pcnt
1732277696	420 Pkt	160 Pkt	87 Pcnt
1732276795	370 Pkt	140 Pkt	86 Pcnt
1732275894	330 Pkt	120 Pkt	85 Pcnt
1732274993	320 Pkt	130 Pkt	87 Pcnt
1732274093	290 Pkt	110 Pkt	85 Pcnt

*Used Equation Coefficients:

Temp: 0, 0, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)