APRS Track Direct

My position About ☰

reset

BX2AMP-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX2AMP-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1836274130	32.6 C	145 p	435 p	9224 p
1762286134	33.8 C	16 p	44 p	3175 p
1762284933	33.6 C	13 p	43 p	3176 p
1762283735	33.9 C	15 p	44 p	3176 p
1762282533	34.9 C	15 p	42 p	3174 p
1762281333	33.7 C	14 p	40 p	3172 p
1762280134	32.8 C	13 p	43 p	3169 p
1762278933	33.2 C	13 p	43 p	3167 p
1762277733	34.3 C	17 p	41 p	3164 p
1762276533	35.2 C	13 p	39 p	3163 p
1762275334	35 C	11 p	43 p	3165 p
1762274134	34.3 C	15 p	61 p	3166 p
1762272933	35.1 C	17 p	98 p	3165 p
1762271733	35.2 C	29 p	128 p	3188 p
1762270534	34.6 C	52 p	144 p	3213 p
1762269333	34.2 C	47 p	140 p	3207 p
1762268133	33.7 C	45 p	135 p	3199 p
1762266933	34.2 C	48 p	168 p	3189 p
1762265734	33.7 C	42 p	185 p	3176 p
1762264534	34 C	78 p	231 p	3161 p
1762263334	34.5 C	65 p	208 p	3117 p
1762262133	34.3 C	88 p	189 p	3065 p
1762260933	33.9 C	55 p	126 p	2993 p
1762259734	34 C	46 p	108 p	2956 p
1762258533	33.8 C	25 p	150 p	2920 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)