APRS Track Direct

My position About ☰

reset

TB1USA-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TB1USA-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274374	0 Pkt	-62 dBm	11.89 V
1836274202	0 Pkt	-62 dBm	11.87 V
1778030567	1 Pkt	-60 dBm	11.87 V
1778029643	1 Pkt	-58 dBm	11.87 V
1778028718	1 Pkt	-59 dBm	11.87 V
1778027799	1 Pkt	-58 dBm	11.89 V
1778026875	1 Pkt	-58 dBm	11.89 V
1778025950	1 Pkt	-62 dBm	11.87 V
1778025031	1 Pkt	-59 dBm	11.89 V
1778024110	1 Pkt	-61 dBm	11.89 V
1778023184	0 Pkt	-60 dBm	11.87 V
1778022264	1 Pkt	-61 dBm	11.87 V
1778021340	2 Pkt	-61 dBm	11.89 V
1778020420	2 Pkt	-61 dBm	11.87 V
1778019496	1 Pkt	-59 dBm	11.89 V
1778018574	1 Pkt	-60 dBm	11.89 V
1778017654	1 Pkt	-59 dBm	11.87 V
1778016730	1 Pkt	-59 dBm	11.87 V
1778015808	1 Pkt	-58 dBm	11.85 V
1778014886	1 Pkt	-59 dBm	11.85 V
1778013965	1 Pkt	-60 dBm	11.87 V
1778013042	2 Pkt	-59 dBm	11.87 V
1778012120	2 Pkt	-60 dBm	11.87 V
1778011198	1 Pkt	-60 dBm	11.89 V
1778010276	1 Pkt	-59 dBm	11.87 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)