APRS Track Direct

My position About ☰

reset

LZ2SMX-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LZ2SMX-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Tbsmt*	Rh*	Tfl1*	Tktcn*	Tloft*
1786740067	26 C	58 %	26 C	27 C	26 C
1786738867	26 C	58 %	26 C	26 C	26 C
1786737667	27 C	58 %	26 C	27 C	26 C
1786736467	26 C	58 %	26 C	26 C	27 C
1786735266	27 C	58 %	26 C	26 C	27 C
1786734066	26 C	58 %	26 C	27 C	27 C
1786732867	27 C	58 %	26 C	27 C	27 C
1786731667	27 C	58 %	26 C	27 C	28 C
1786730468	27 C	58 %	26 C	27 C	28 C
1786729267	27 C	58 %	26 C	27 C	28 C
1786728067	27 C	58 %	26 C	27 C	29 C
1786726867	27 C	58 %	26 C	27 C	29 C
1786725668	27 C	58 %	27 C	27 C	29 C
1786724468	27 C	58 %	27 C	27 C	30 C
1786723268	27 C	58 %	27 C	27 C	30 C
1786722067	27 C	58 %	27 C	27 C	30 C
1786720867	27 C	58 %	27 C	27 C	30 C
1786719668	27 C	58 %	27 C	27 C	30 C
1786718467	27 C	58 %	27 C	27 C	30 C
1786717268	27 C	58 %	27 C	27 C	30 C
1786716068	27 C	58 %	27 C	27 C	30 C
1786714868	27 C	58 %	27 C	27 C	30 C
1786713668	27 C	58 %	27 C	27 C	30 C
1786712467	27 C	58 %	27 C	27 C	30 C
1786711267	27 C	58 %	26 C	27 C	30 C

*Used Equation Coefficients:

Tbsmt: 0, 1, 0

Rh: 0, 1, 0

Tfl1: 0, 1, 0

Tktcn: 0, 1, 0

Tloft: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)