APRS Track Direct

My position About ☰

reset

BX6AM-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6AM-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790661825	49.4 C	18 p	69 p	2823 p
1790660625	49.1 C	26 p	78 p	2828 p
1790659425	48.5 C	25 p	96 p	2833 p
1790658224	48.9 C	27 p	95 p	2843 p
1790657025	50 C	44 p	89 p	2849 p
1790655824	49.1 C	24 p	67 p	2853 p
1790654625	48.7 C	21 p	67 p	2858 p
1790653425	49.1 C	22 p	69 p	2864 p
1790652225	50.4 C	24 p	75 p	2870 p
1790651025	49.9 C	23 p	90 p	2876 p
1790649825	48.9 C	28 p	95 p	2879 p
1790648625	47.7 C	39 p	100 p	2883 p
1790647425	48.6 C	28 p	96 p	2873 p
1790646225	48.5 C	33 p	104 p	2876 p
1790645024	48.8 C	35 p	105 p	2874 p
1790643825	48.5 C	36 p	102 p	2871 p
1790642625	48.2 C	34 p	96 p	2867 p
1790641425	48 C	32 p	99 p	2882 p
1790640225	47 C	30 p	101 p	2899 p
1790639025	48.5 C	37 p	101 p	2897 p
1790637826	47.5 C	34 p	94 p	2893 p
1790636625	47.5 C	30 p	91 p	2888 p
1790635426	47.2 C	30 p	92 p	2892 p
1790634226	47 C	31 p	94 p	2892 p
1790633026	47.6 C	31 p	98 p	2892 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)