APRS Track Direct

My position About ☰

reset

SR9POD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9POD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	T_in*	Rx1h*	Dg1h*
1745051606	13.65 Volt	27 C	370 Pkt	80 Pkt
1745051013	13.65 Volt	26.5 C	350 Pkt	70 Pkt
1745050406	13.65 Volt	26.5 C	390 Pkt	80 Pkt
1745049807	13.65 Volt	26 C	370 Pkt	70 Pkt
1745049210	13.65 Volt	25.5 C	340 Pkt	70 Pkt
1745048610	13.65 Volt	25 C	340 Pkt	70 Pkt
1745048007	13.65 Volt	24.5 C	350 Pkt	70 Pkt
1745047406	13.65 Volt	24 C	310 Pkt	70 Pkt
1745046806	13.65 Volt	24 C	330 Pkt	70 Pkt
1745046207	13.65 Volt	24 C	320 Pkt	70 Pkt
1745045606	13.65 Volt	23.5 C	330 Pkt	80 Pkt
1745045008	13.65 Volt	23.5 C	350 Pkt	80 Pkt
1745044407	13.65 Volt	23.5 C	360 Pkt	80 Pkt
1745043207	13.65 Volt	23 C	360 Pkt	80 Pkt
1745042608	13.65 Volt	22.5 C	350 Pkt	80 Pkt
1745042008	13.65 Volt	22 C	330 Pkt	80 Pkt
1745041406	13.58 Volt	22 C	330 Pkt	80 Pkt
1745040807	13.65 Volt	21.5 C	350 Pkt	80 Pkt
1745040208	13.5 Volt	21.5 C	320 Pkt	70 Pkt
1745039607	13.58 Volt	21 C	340 Pkt	80 Pkt
1745039007	13.65 Volt	21 C	320 Pkt	70 Pkt
1745037807	13.65 Volt	21 C	320 Pkt	70 Pkt
1745037207	13.65 Volt	21 C	320 Pkt	70 Pkt
1745036607	13.65 Volt	21 C	300 Pkt	60 Pkt
1745036007	13.65 Volt	20.5 C	310 Pkt	60 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

T_in: 0, 0.5, -64

T_out: 0, 1, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)