APRS Track Direct

My position About ☰

reset

VK4RBY-B Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK4RBY-B. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Tx5m*	CPU-c*	Mem%*	RPTxT*
1786734001	0 Count	45 degC	10 Pct	0 Min
1786732201	0 Count	45 degC	10 Pct	0 Min
1786730401	0 Count	45 degC	11 Pct	0 Min
1786728601	0 Count	45 degC	10 Pct	0 Min
1786726801	0 Count	45 degC	10 Pct	0 Min
1786725001	0 Count	46 degC	11 Pct	0 Min
1786723201	0 Count	45 degC	11 Pct	0 Min
1786721401	0 Count	45 degC	11 Pct	0 Min
1786719601	0 Count	46 degC	10 Pct	0 Min
1786717801	0 Count	44 degC	10 Pct	0 Min
1786716001	0 Count	44 degC	10 Pct	0 Min
1786714201	0 Count	42 degC	10 Pct	19 Min
1786712401	0 Count	45 degC	10 Pct	19 Min
1786710601	0 Count	45 degC	10 Pct	3 Min
1786708801	0 Count	44 degC	11 Pct	1 Min
1786707001	0 Count	43 degC	11 Pct	1 Min
1786705201	0 Count	43 degC	11 Pct	1 Min
1786703401	0 Count	42 degC	11 Pct	1 Min
1786701601	0 Count	43 degC	11 Pct	1 Min
1786699801	0 Count	43 degC	11 Pct	0 Min
1786698001	0 Count	42 degC	10 Pct	0 Min
1786696201	0 Count	42 degC	10 Pct	0 Min
1786694401	0 Count	43 degC	10 Pct	0 Min
1786692601	1 Count	43 degC	10 Pct	0 Min
1786690801	0 Count	47 degC	10 Pct	0 Min

*Used Equation Coefficients:

Tx5m: 0, 1, 0

Rx5m: 0, 1, 0

CPU-c: 0, 1, 20

Mem%: 0, 1, 0

RPTxT: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)