This is the latest recevied telemetry packets stored in our database for station/object DL0TRZ-20. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Volt* | Ampere* | Batt* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1836274197 | 12.7 V | 0 A | 0 V | 0 | 0 |
| 1779799540 | 13.2 V | 0 A | 0 V | 0 | 0 |
| 1779797747 | 13.1 V | 0 A | 0 V | 0 | 0 |
| 1779797725 | 13.1 V | 0 A | 0 V | 0 | 0 |
| 1779795930 | 13.1 V | 0 A | 0 V | 0 | 0 |
| 1779795910 | 13.1 V | 0 A | 0 V | 0 | 0 |
| 1779794111 | 13.1 V | 0 A | 0 V | 0 | 0 |
| 1779794095 | 13.1 V | 0 A | 0 V | 0 | 0 |
| 1779792280 | 13.2 V | 0 A | 0 V | 0 | 0 |
| 1779790465 | 12.9 V | 0 A | 0 V | 0 | 0 |
| 1779788650 | 12.7 V | 0 A | 0 V | 0 | 0 |
| 1779786835 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779785020 | 12.9 V | 0 A | 0 V | 0 | 0 |
| 1779783244 | 12.7 V | 0 A | 0 V | 0 | 0 |
| 1779783205 | 12.7 V | 0 A | 0 V | 0 | 0 |
| 1779781445 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779781390 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779779581 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779779578 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779777760 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779775989 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779775945 | 12.6 V | 0 A | 0 V | 0 | 0 |
| 1779774130 | 12.3 V | 0 A | 0 V | 0 | 0 |
| 1779772315 | 12.2 V | 0 A | 0 V | 0 | 0 |
| 1779770500 | 12.2 V | 0 A | 0 V | 0 | 0 |
*Used Equation Coefficients:
Volt: 0, 1, 0
Ampere: 0, 1, 0
Batt: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)