APRS Track Direct

My position About ☰

reset

DB0LSB Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0LSB. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1745056526	13.65 Volt	130 Pkt	50 Pkt	59 Pcnt
1745055926	13.65 Volt	110 Pkt	40 Pkt	49 Pcnt
1745055325	13.5 Volt	90 Pkt	30 Pkt	42 Pcnt
1745053526	13.58 Volt	70 Pkt	20 Pkt	36 Pcnt
1745052923	13.88 Volt	80 Pkt	30 Pkt	43 Pcnt
1745052325	13.8 Volt	100 Pkt	40 Pkt	54 Pcnt
1745051722	13.8 Volt	110 Pkt	40 Pkt	57 Pcnt
1745051121	13.8 Volt	130 Pkt	50 Pkt	64 Pcnt
1745050522	13.65 Volt	150 Pkt	60 Pkt	68 Pcnt
1745049920	13.58 Volt	160 Pkt	70 Pkt	72 Pcnt
1745049320	13.58 Volt	170 Pkt	70 Pkt	69 Pcnt
1745048719	13.5 Volt	180 Pkt	70 Pkt	71 Pcnt
1745048118	13.28 Volt	190 Pkt	70 Pkt	73 Pcnt
1745047518	13.2 Volt	200 Pkt	70 Pkt	72 Pcnt
1745046917	13.2 Volt	210 Pkt	70 Pkt	72 Pcnt
1745046317	13.05 Volt	210 Pkt	70 Pkt	71 Pcnt
1745045716	12.9 Volt	210 Pkt	80 Pkt	74 Pcnt
1745045116	12.83 Volt	200 Pkt	80 Pkt	72 Pcnt
1745044516	12.75 Volt	190 Pkt	80 Pkt	70 Pcnt
1745042716	12.68 Volt	170 Pkt	70 Pkt	68 Pcnt
1745042113	12.68 Volt	170 Pkt	70 Pkt	69 Pcnt
1745040311	12.68 Volt	200 Pkt	70 Pkt	77 Pcnt
1745039712	12.68 Volt	200 Pkt	70 Pkt	79 Pcnt
1745038509	12.6 Volt	200 Pkt	70 Pkt	79 Pcnt
1745037910	12.6 Volt	190 Pkt	70 Pkt	79 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)