APRS Track Direct

My position About ☰

reset

DM0DOS-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DM0DOS-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx1h*	Vin*	Temp*
1786785985	260 Pkt	12.38 Volt	25 C
1786785385	360 Pkt	12.38 Volt	25 C
1786784785	400 Pkt	12.38 Volt	24.5 C
1786784185	400 Pkt	12.38 Volt	24.5 C
1786783585	430 Pkt	12.38 Volt	24.5 C
1786782985	510 Pkt	12.38 Volt	24.5 C
1786782385	550 Pkt	12.38 Volt	24.5 C
1786781785	600 Pkt	12.38 Volt	24.5 C
1786781185	750 Pkt	12.38 Volt	24.5 C
1786780585	890 Pkt	12.38 Volt	24 C
1786779985	1050 Pkt	12.38 Volt	24 C
1786779385	1190 Pkt	12.38 Volt	24 C
1786778785	1360 Pkt	12.38 Volt	24 C
1786778185	1480 Pkt	12.38 Volt	24 C
1786777585	1550 Pkt	12.38 Volt	24 C
1786776985	1600 Pkt	12.38 Volt	24 C
1786776385	1560 Pkt	12.38 Volt	24 C
1786775785	1540 Pkt	12.38 Volt	24 C
1786775185	1510 Pkt	12.38 Volt	24 C
1786774585	1440 Pkt	12.38 Volt	24.5 C
1786773985	1430 Pkt	12.38 Volt	24.5 C
1786773385	1440 Pkt	12.38 Volt	24.5 C
1786772785	1470 Pkt	12.38 Volt	24.5 C
1786772185	1530 Pkt	12.38 Volt	24.5 C
1786771585	1560 Pkt	12.38 Volt	25 C

*Used Equation Coefficients:

Rx1h: 0, 10, 0

Vin: 0, 0.075, 0

Temp: 0, 0.5, -64

Value4: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)