APRS Track Direct

My position About ☰

reset

TA1KNN-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA1KNN-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274448	8 Pkt	-62 dBm	10.73 V
1774114154	5 Pkt	-66 dBm	10.71 V
1774113231	3 Pkt	-69 dBm	10.73 V
1774112309	5 Pkt	-69 dBm	10.71 V
1774111387	3 Pkt	-70 dBm	10.73 V
1774110465	7 Pkt	-65 dBm	10.73 V
1774109542	7 Pkt	-72 dBm	10.71 V
1774108621	8 Pkt	-72 dBm	10.73 V
1774107698	2 Pkt	-70 dBm	10.71 V
1774107030	1 Pkt	-73 dBm	10.71 V
1774106839	5 Pkt	-74 dBm	10.73 V
1774105916	7 Pkt	-74 dBm	10.71 V
1774104994	3 Pkt	-72 dBm	10.73 V
1774104071	6 Pkt	-74 dBm	10.71 V
1774103148	11 Pkt	-73 dBm	10.71 V
1774102225	8 Pkt	-73 dBm	10.71 V
1774101302	7 Pkt	-76 dBm	10.71 V
1774100380	7 Pkt	-74 dBm	10.73 V
1774099458	4 Pkt	-75 dBm	10.71 V
1774098536	10 Pkt	-74 dBm	10.71 V
1774097612	6 Pkt	-73 dBm	10.71 V
1774096689	19 Pkt	-73 dBm	10.73 V
1774095766	6 Pkt	-71 dBm	10.73 V
1774094845	5 Pkt	-72 dBm	10.71 V
1774093921	5 Pkt	-72 dBm	10.71 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)