APRS Track Direct

My position About ☰

reset

BM6HIP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HIP-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1836274508	25.8 C	37 p	83 p	2442 p
1766200939	23.7 C	35 p	126 p	2294 p
1766199740	22.9 C	43 p	128 p	2290 p
1766198539	23 C	48 p	111 p	2278 p
1766197340	23.1 C	37 p	101 p	2253 p
1766196140	22.9 C	26 p	104 p	2261 p
1766194939	23.5 C	38 p	116 p	2270 p
1766193739	23.4 C	40 p	113 p	2261 p
1766192539	23.4 C	38 p	110 p	2250 p
1766191340	23.7 C	35 p	106 p	2244 p
1766190140	23.7 C	37 p	105 p	2267 p
1766188939	23.9 C	34 p	96 p	2293 p
1766187740	23.3 C	34 p	93 p	2293 p
1766186540	23.7 C	28 p	144 p	2290 p
1766185340	23.4 C	31 p	195 p	2285 p
1766184140	24 C	85 p	204 p	2280 p
1766182940	24 C	79 p	140 p	2229 p
1766181739	23.9 C	40 p	89 p	2179 p
1766180540	23 C	21 p	75 p	2163 p
1766179339	24.1 C	28 p	99 p	2170 p
1766178141	23.6 C	26 p	100 p	2172 p
1766176939	23.6 C	45 p	101 p	2170 p
1766175741	23.5 C	29 p	83 p	2169 p
1766174540	23.9 C	27 p	93 p	2169 p
1766173340	24.5 C	27 p	98 p	2165 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)