APRS Track Direct

My position About ☰

reset

LU1HD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU1HD-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1836274421	0 Pkt	-62 dBm	14.29 V
1769243224	0 Pkt	-57 dBm	14.31 V
1769241402	0 Pkt	-58 dBm	14.29 V
1769239580	1 Pkt	-58 dBm	14.27 V
1769237758	1 Pkt	-56 dBm	14.27 V
1769235935	1 Pkt	-57 dBm	14.29 V
1769234113	1 Pkt	-59 dBm	14.31 V
1769232291	5 Pkt	-58 dBm	14.29 V
1769230469	18 Pkt	-56 dBm	14.29 V
1769228644	5 Pkt	-56 dBm	14.23 V
1769226821	3 Pkt	-58 dBm	14.27 V
1769224999	4 Pkt	-58 dBm	14.29 V
1769223177	5 Pkt	-57 dBm	14.29 V
1769221354	3 Pkt	-58 dBm	14.27 V
1769219532	3 Pkt	-55 dBm	14.31 V
1769217709	1 Pkt	-64 dBm	14.29 V
1769215887	3 Pkt	-62 dBm	14.29 V
1769214064	3 Pkt	-63 dBm	14.31 V
1769212242	5 Pkt	-64 dBm	14.29 V
1769210420	0 Pkt	-65 dBm	14.29 V
1769208521	5 Pkt	-60 dBm	14.23 V
1769206699	4 Pkt	-55 dBm	14.27 V
1769204876	1 Pkt	-56 dBm	14.29 V
1769203054	3 Pkt	-55 dBm	14.29 V
1769201232	2 Pkt	-57 dBm	14.23 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)