APRS Track Direct

My position About ☰

reset

OY6FRA-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OY6FRA-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RFIn*	RFiGate*	DigiRpt*	Temp*
1770390045	11 Pkts	11 Pkts	11 Pkts	19 C
1770386445	11 Pkts	11 Pkts	11 Pkts	19 C
1770382861	8 Pkts	8 Pkts	7 Pkts	18 C
1770379245	13 Pkts	13 Pkts	13 Pkts	19 C
1770372045	9 Pkts	9 Pkts	8 Pkts	19 C
1770368445	9 Pkts	9 Pkts	9 Pkts	19 C
1770361247	8 Pkts	8 Pkts	8 Pkts	19 C
1770354047	10 Pkts	10 Pkts	9 Pkts	18 C
1770350445	10 Pkts	10 Pkts	9 Pkts	18 C
1770346845	8 Pkts	8 Pkts	7 Pkts	18 C
1770343246	12 Pkts	12 Pkts	10 Pkts	19 C
1770339645	11 Pkts	11 Pkts	11 Pkts	19 C
1770336045	11 Pkts	11 Pkts	10 Pkts	18 C
1770332446	14 Pkts	14 Pkts	14 Pkts	19 C
1770328845	16 Pkts	16 Pkts	15 Pkts	19 C
1770325247	12 Pkts	12 Pkts	11 Pkts	19 C
1770321645	20 Pkts	20 Pkts	20 Pkts	18 C
1770318045	16 Pkts	16 Pkts	15 Pkts	18 C
1770314445	19 Pkts	19 Pkts	19 Pkts	18 C
1770310845	18 Pkts	18 Pkts	18 Pkts	19 C
1770307245	20 Pkts	20 Pkts	19 Pkts	19 C

*Used Equation Coefficients:

RFIn: 0, 1, 0

RFiGate: 0, 1, 0

DigiRpt: 0, 1, 0

Temp: 0, 1, 0

InetiGate: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)