APRS Track Direct

My position About ☰

reset

LW8EXS-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LW8EXS-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RxTraffic*	TxTraffic*	RxDrop*	RSSI*	Voltage*
1790652354	34 Pkt	13 Pkt	2 Pkt	-53 dBm	12.84 V
1790648851	64 Pkt	17 Pkt	4 Pkt	-43 dBm	12.84 V
1790645347	48 Pkt	16 Pkt	6 Pkt	-40 dBm	12.84 V
1790641843	73 Pkt	20 Pkt	0 Pkt	-41 dBm	12.84 V
1790638336	57 Pkt	3 Pkt	1 Pkt	-52 dBm	12.86 V
1790634832	53 Pkt	3 Pkt	0 Pkt	-44 dBm	12.84 V
1790631329	38 Pkt	3 Pkt	0 Pkt	-47 dBm	12.88 V
1790627826	44 Pkt	4 Pkt	1 Pkt	-48 dBm	12.88 V
1790624316	35 Pkt	5 Pkt	1 Pkt	-38 dBm	12.88 V
1790620811	65 Pkt	6 Pkt	1 Pkt	-41 dBm	12.88 V
1790617307	54 Pkt	6 Pkt	1 Pkt	-37 dBm	12.88 V
1790613802	59 Pkt	6 Pkt	9 Pkt	-36 dBm	12.88 V
1790610297	56 Pkt	5 Pkt	3 Pkt	-43 dBm	12.88 V
1790606793	58 Pkt	3 Pkt	4 Pkt	-40 dBm	12.88 V
1790603289	43 Pkt	2 Pkt	3 Pkt	-43 dBm	12.88 V
1790599784	0 Pkt	0 Pkt	0 Pkt	-41 dBm	12.88 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)