APRS Track Direct

My position About ☰

reset

AI5TX-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object AI5TX-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1782540157	13.35 Volt	50 Pkt	20 Pkt	23 Pcnt
1782536557	13.28 Volt	30 Pkt	10 Pkt	18 Pcnt
1782532957	13.28 Volt	10 Pkt	0 Pkt	18 Pcnt
1782529357	13.28 Volt	20 Pkt	10 Pkt	42 Pcnt
1782525757	13.35 Volt	10 Pkt	10 Pkt	33 Pcnt
1782522157	13.28 Volt	10 Pkt	10 Pkt	32 Pcnt
1782518557	13.28 Volt	0 Pkt	0 Pkt	15 Pcnt
1782514958	13.28 Volt	30 Pkt	10 Pkt	47 Pcnt
1782511358	13.35 Volt	20 Pkt	10 Pkt	26 Pcnt
1782507758	13.28 Volt	20 Pkt	10 Pkt	23 Pcnt
1782504158	13.28 Volt	30 Pkt	10 Pkt	34 Pcnt
1782500558	13.28 Volt	10 Pkt	10 Pkt	20 Pcnt
1782496958	13.28 Volt	10 Pkt	10 Pkt	19 Pcnt
1782493358	13.28 Volt	10 Pkt	10 Pkt	15 Pcnt
1782489758	13.28 Volt	40 Pkt	20 Pkt	23 Pcnt
1782486158	13.28 Volt	60 Pkt	30 Pkt	31 Pcnt
1782482558	13.28 Volt	20 Pkt	10 Pkt	18 Pcnt
1782478958	13.28 Volt	60 Pkt	20 Pkt	30 Pcnt
1782475359	13.28 Volt	30 Pkt	10 Pkt	16 Pcnt
1782471759	13.28 Volt	30 Pkt	20 Pkt	21 Pcnt
1782468159	13.28 Volt	30 Pkt	10 Pkt	22 Pcnt
1782464559	13.28 Volt	100 Pkt	80 Pkt	44 Pcnt
1782460959	13.28 Volt	40 Pkt	20 Pkt	19 Pcnt
1782457359	13.28 Volt	40 Pkt	20 Pkt	16 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)