APRS Track Direct

My position About ☰

reset

DG2MCM-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DG2MCM-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	VOC*	PM2.5*	PM10*	PM1.0*
1790656596	67 idx	0.05 ug	0.05 ug	0.04 ug
1790655995	70 idx	0.04 ug	0.04 ug	0.04 ug
1790655394	73 idx	0.04 ug	0.04 ug	0.04 ug
1790654192	79 idx	0.04 ug	0.04 ug	0.04 ug
1790652990	86 idx	0.04 ug	0.04 ug	0.04 ug
1790651788	94 idx	0.04 ug	0.04 ug	0.04 ug
1790651188	98 idx	0.04 ug	0.04 ug	0.04 ug
1790650587	102 idx	0.03 ug	0.03 ug	0.03 ug
1790649986	107 idx	0.04 ug	0.04 ug	0.04 ug
1790648784	116 idx	0.03 ug	0.03 ug	0.03 ug
1790647582	123 idx	0.03 ug	0.03 ug	0.03 ug
1790646981	125 idx	0.03 ug	0.03 ug	0.03 ug
1790646380	126 idx	0.03 ug	0.03 ug	0.03 ug
1790645779	127 idx	0.02 ug	0.02 ug	0.02 ug
1790644577	127 idx	0.02 ug	0.02 ug	0.02 ug
1790643976	127 idx	0.01 ug	0.01 ug	0.01 ug
1790643375	127 idx	0.01 ug	0.01 ug	0.01 ug
1790642774	127 idx	0.01 ug	0.01 ug	0.01 ug
1790640971	127 idx	0.01 ug	0.01 ug	0.01 ug
1790640370	127 idx	0.01 ug	0.01 ug	0.01 ug
1790636163	127 idx	0.01 ug	0.01 ug	0.01 ug
1790635563	128 idx	0.02 ug	0.02 ug	0.02 ug
1790634962	128 idx	0.01 ug	0.01 ug	0.01 ug
1790634361	128 idx	0.01 ug	0.01 ug	0.01 ug
1790633760	128 idx	0.01 ug	0.01 ug	0.01 ug

*Used Equation Coefficients:

CO2: 0, 10, 0

VOC: 0, 1, 0

PM2.5: 0, 0.01, 0

PM10: 0, 0.01, 0

PM1.0: 0, 0.01, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)