This is the latest recevied telemetry packets stored in our database for station/object IU3ISP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1758178012 | 998 VDC | 505 | 482 | 0 | 0 |
| 1758176208 | 997 VDC | 505 | 482 | 0 | 0 |
| 1758174404 | 994 VDC | 503 | 480 | 0 | 0 |
| 1758172600 | 991 VDC | 501 | 478 | 0 | 0 |
| 1758168992 | 986 VDC | 498 | 475 | 0 | 0 |
| 1758167188 | 983 VDC | 496 | 473 | 0 | 0 |
| 1758165384 | 981 VDC | 495 | 472 | 0 | 0 |
| 1758163580 | 979 VDC | 494 | 471 | 0 | 0 |
| 1758161776 | 976 VDC | 492 | 469 | 0 | 0 |
| 1758159973 | 973 VDC | 490 | 467 | 0 | 0 |
| 1758158212 | 966 VDC | 488 | 465 | 0 | 0 |
| 1758156409 | 964 VDC | 487 | 464 | 0 | 0 |
| 1758154605 | 961 VDC | 485 | 462 | 0 | 0 |
| 1758152801 | 958 VDC | 483 | 460 | 0 | 0 |
| 1758150997 | 956 VDC | 482 | 459 | 0 | 0 |
| 1758149193 | 954 VDC | 481 | 458 | 0 | 0 |
| 1758145585 | 951 VDC | 480 | 457 | 0 | 0 |
| 1758140173 | 948 VDC | 480 | 457 | 0 | 0 |
| 1758138369 | 946 VDC | 479 | 456 | 0 | 0 |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 0.01, 0
V_Ext: 0, 0.02, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)