APRS Track Direct

My position About ☰

reset

VR2WUK Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VR2WUK. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	CPU*	Temp*	FreeM*
1758219955	0.24 Load	49.39 °C	642 Mb
1758219646	0.27 Load	48.31 °C	643 Mb
1758219346	0.24 Load	48.85 °C	642 Mb
1758219036	0.27 Load	48.31 °C	642 Mb
1758218726	0.23 Load	48.85 °C	641 Mb
1758218427	0.27 Load	49.39 °C	642 Mb
1758218117	0.22 Load	49.39 °C	642 Mb
1758217807	0.24 Load	49.39 °C	642 Mb
1758217507	0.23 Load	49.39 °C	642 Mb
1758217197	0.28 Load	48.31 °C	641 Mb
1758216887	0.26 Load	48.85 °C	643 Mb
1758216588	0.24 Load	49.39 °C	643 Mb
1758216278	0.27 Load	49.39 °C	643 Mb
1758215968	0.23 Load	48.85 °C	644 Mb
1758215668	0.29 Load	48.31 °C	642 Mb
1758215358	0.25 Load	49.39 °C	642 Mb
1758215048	0.27 Load	49.39 °C	642 Mb
1758214749	0.24 Load	49.39 °C	643 Mb
1758214439	0.22 Load	49.39 °C	642 Mb
1758214129	0.23 Load	48.31 °C	645 Mb
1758213829	0.23 Load	49.39 °C	644 Mb
1758213520	0.26 Load	48.85 °C	644 Mb
1758213210	0.22 Load	48.31 °C	645 Mb
1758212910	0.29 Load	49.39 °C	645 Mb
1758212600	0.26 Load	48.85 °C	645 Mb

*Used Equation Coefficients:

CPU: 0, 0.001, 0

Temp: 0, 0.001, 0

FreeM: 0, 1, 0

RxP: 0, 1, 0

TxP: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)