APRS Track Direct

My position About ☰

reset

E24SAT-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object E24SAT-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	TxTraffic*	RSSI*	Voltage*
1758177188	8 Pkt	-83 dBm	12.71 V
1758175363	7 Pkt	-82 dBm	12.69 V
1758173537	6 Pkt	-82 dBm	12.63 V
1758171712	10 Pkt	-81 dBm	12.63 V
1758169886	10 Pkt	-82 dBm	12.63 V
1758168061	4 Pkt	-83 dBm	12.63 V
1758166236	10 Pkt	-81 dBm	12.61 V
1758164410	4 Pkt	-82 dBm	12.65 V
1758162585	9 Pkt	-81 dBm	12.65 V
1758160760	13 Pkt	-82 dBm	12.69 V
1758158934	17 Pkt	-82 dBm	12.67 V
1758157108	5 Pkt	-82 dBm	12.69 V
1758155283	0 Pkt	-83 dBm	12.67 V
1758153458	1 Pkt	-86 dBm	12.65 V
1758151632	0 Pkt	-84 dBm	12.67 V
1758149807	0 Pkt	-84 dBm	12.69 V
1758147982	0 Pkt	-84 dBm	12.67 V
1758146157	1 Pkt	-85 dBm	12.65 V
1758144332	0 Pkt	-86 dBm	12.65 V
1758142507	0 Pkt	-85 dBm	12.67 V
1758140682	0 Pkt	-86 dBm	12.67 V
1758138857	0 Pkt	-86 dBm	12.67 V
1758137290	0 Pkt	-84 dBm	12.67 V
1758135208	0 Pkt	-85 dBm	12.67 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)