APRS Track Direct

My position About ☰

reset

BM6HFL-6 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HFL-6. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1836274583	43.1 C	0 p	2 p	50 p
1836274134	43.5 C	1 p	2 p	51 p
1774127535	33.8 C	1 p	4 p	76 p
1774126334	32.7 C	2 p	4 p	76 p
1774125135	32.6 C	1 p	3 p	76 p
1774123934	32.3 C	1 p	2 p	75 p
1774122735	33.6 C	1 p	2 p	75 p
1774121534	35.9 C	0 p	2 p	75 p
1774120334	36.2 C	1 p	2 p	75 p
1774119135	34.6 C	1 p	2 p	75 p
1774117935	34.8 C	0 p	1 p	77 p
1774116734	36.7 C	1 p	1 p	77 p
1774115534	35.7 C	0 p	1 p	81 p
1774114335	36.2 C	0 p	2 p	84 p
1774113135	35.5 C	1 p	2 p	84 p
1774111935	36.2 C	1 p	2 p	84 p
1774110735	35.6 C	0 p	2 p	83 p
1774109534	37.1 C	1 p	2 p	83 p
1774108334	35.4 C	1 p	2 p	82 p
1774107135	35.9 C	0 p	4 p	82 p
1774105935	35 C	1 p	4 p	82 p
1774104734	36.5 C	3 p	4 p	81 p
1774103535	36.7 C	0 p	3 p	78 p
1774102334	36.7 C	1 p	4 p	78 p
1774101135	36.6 C	2 p	4 p	77 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)