APRS Track Direct

My position About ☰

reset

VK6RTH-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object VK6RTH-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Temp*	Supply*	ADC0*
1790659360	23.08 DegC	13.02 Volt	250 None
1790657554	23.08 DegC	13.73 Volt	251 None
1790655746	21.12 DegC	13.33 Volt	250 None
1790653923	21.12 DegC	12.94 Volt	250 None
1790652098	21.12 DegC	12.86 Volt	250 None
1790650287	23.08 DegC	13.1 Volt	250 None
1790648480	21.12 DegC	13.1 Volt	250 None
1790646666	19.16 DegC	13.25 Volt	249 None
1790644854	19.16 DegC	13.1 Volt	250 None
1790643050	19.16 DegC	13.1 Volt	249 None
1790641242	19.16 DegC	12.86 Volt	250 None
1790639439	19.16 DegC	12.39 Volt	249 None
1790637635	19.16 DegC	12.31 Volt	248 None
1790635831	19.16 DegC	12.24 Volt	249 None
1790634026	19.16 DegC	12.24 Volt	248 None
1790632219	21.12 DegC	12.24 Volt	248 None
1790630412	19.16 DegC	12.24 Volt	248 None
1790628607	19.16 DegC	12.24 Volt	248 None
1790626802	19.16 DegC	12.31 Volt	249 None
1790624999	19.16 DegC	12.31 Volt	248 None
1790623194	21.12 DegC	12.24 Volt	248 None
1790621389	21.12 DegC	12.31 Volt	248 None
1790619587	21.12 DegC	12.31 Volt	248 None
1790617783	21.12 DegC	12.31 Volt	248 None
1790615977	21.12 DegC	12.31 Volt	248 None

*Used Equation Coefficients:

Temp: 0, 1.9608, -273

Supply: 0, 0.07843, 0

ADC0: 0, 1, 0

Cnt: 0, 1, 0

HDOP: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)