APRS Track Direct

My position About ☰

reset

SP3TLU-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP3TLU-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Radiation*	PV-7.8kW*
1836274679	0.24 uSv/h	0 kW
1836274499	0.16 uSv/h	0 kW
1836274469	0.32 uSv/h	0 kW
1836274319	0.08 uSv/h	0 kW
1836274289	0.16 uSv/h	0 kW
1836274139	0.16 uSv/h	0 kW
1836274109	0.08 uSv/h	0 kW
1836273959	0.08 uSv/h	0 kW
1762326723	0.17 uSv/h	0.35 kW
1762326542	0.13 uSv/h	0.33 kW
1762326362	0.08 uSv/h	0.31 kW
1762326182	0.09 uSv/h	0.29 kW
1762326002	0.14 uSv/h	0.28 kW
1762325822	0.11 uSv/h	0.26 kW
1762325642	0.11 uSv/h	0.26 kW
1762325462	0.06 uSv/h	0.24 kW
1762325282	0.11 uSv/h	0.23 kW
1762325102	0.06 uSv/h	0.22 kW
1762324922	0.17 uSv/h	0.2 kW
1762324742	0.14 uSv/h	0.19 kW
1762324562	0.14 uSv/h	0.18 kW
1762324382	0.19 uSv/h	0.16 kW
1762324202	0.09 uSv/h	0.13 kW
1762324022	0.08 uSv/h	0.11 kW
1762323842	0.09 uSv/h	0.09 kW

*Used Equation Coefficients:

Radiation: 0, 0.001, 0

PV-7.8kW: 0, 0.001, 0

PM2.5: 0, 0.1, 0

PM10: 0, 0.1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)