APRS Track Direct

My position About ☰

reset

BM6HIP-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HIP-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790656916	54.6 C	6 p	22 p	2625 p
1790655716	53.7 C	8 p	24 p	2626 p
1790654516	53.9 C	8 p	22 p	2626 p
1790653316	53.8 C	8 p	23 p	2627 p
1790652116	53.8 C	6 p	25 p	2628 p
1790650916	53.5 C	9 p	25 p	2631 p
1790649716	53.5 C	10 p	25 p	2629 p
1790648516	53.7 C	6 p	27 p	2627 p
1790647316	53.3 C	9 p	35 p	2625 p
1790646116	53.9 C	12 p	38 p	2623 p
1790644916	54.5 C	14 p	31 p	2617 p
1790643716	53.9 C	12 p	22 p	2607 p
1790642516	53.5 C	5 p	22 p	2619 p
1790641317	53.9 C	5 p	27 p	2620 p
1790640119	55.7 C	12 p	32 p	2625 p
1790638917	53.3 C	10 p	36 p	2620 p
1790637716	52.2 C	10 p	49 p	2617 p
1790636516	52.9 C	16 p	69 p	2619 p
1790635316	52.2 C	23 p	83 p	2622 p
1790634116	52.1 C	30 p	87 p	2632 p
1790632917	52.3 C	30 p	87 p	2633 p
1790631716	52.5 C	27 p	85 p	2642 p
1790630516	53.2 C	30 p	92 p	2652 p
1790629316	52.8 C	28 p	97 p	2668 p
1790628116	52.7 C	34 p	103 p	2688 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)