APRS Track Direct

My position About ☰

reset

OE1TKS-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE1TKS-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	400Ah*	WrOUT*
1836274670	13.28 Volt	32 +Watt
1836274520	13.28 Volt	32 +Watt
1836274370	13.28 Volt	32 +Watt
1836274220	13.28 Volt	32 +Watt
1836274070	13.28 Volt	32 +Watt
1762318180	13.28 Volt	0 +Watt
1762317880	13.28 Volt	0 +Watt
1762317580	13.28 Volt	0 +Watt
1762317280	13.35 Volt	0 +Watt
1762316980	13.28 Volt	0 +Watt
1762316680	13.28 Volt	0 +Watt
1762316380	13.35 Volt	0 +Watt
1762316080	13.28 Volt	0 +Watt
1762315780	13.28 Volt	0 +Watt
1762315480	13.28 Volt	0 +Watt
1762315180	13.28 Volt	0 +Watt
1762314880	13.28 Volt	0 +Watt
1762314580	13.35 Volt	0 +Watt
1762314280	13.28 Volt	0 +Watt
1762313980	13.28 Volt	0 +Watt
1762313680	13.28 Volt	0 +Watt
1762313380	13.28 Volt	0 +Watt
1762313080	13.28 Volt	0 +Watt
1762312780	13.28 Volt	0 +Watt
1762312480	13.28 Volt	0 +Watt

*Used Equation Coefficients:

Solar: 0, 0.23, 0

Solar: 0, 8.9, -1139.2

Solar: 0, 0.19, -24.32

400Ah: 0, 0.075, 0

WrOUT: 0, 4, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)