APRS Track Direct

My position About ☰

reset

SQ7BFT-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SQ7BFT-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1790663322	0 Pkt	-65 dBm	5.5 V
1790662410	0 Pkt	-67 dBm	5.21 V
1790661488	1 Pkt	-66 dBm	4.8 V
1790660566	0 Pkt	-65 dBm	4.37 V
1790659643	0 Pkt	-65 dBm	3.86 V
1790659187	0 Pkt	-65 dBm	3.51 V
1790658265	0 Pkt	-64 dBm	2.6 V
1790657592	0 Pkt	-64 dBm	1.85 V
1790655631	0 Pkt	-64 dBm	0.16 V
1790654924	0 Pkt	-64 dBm	0.1 V
1790654002	0 Pkt	-64 dBm	0.08 V
1790653186	0 Pkt	-64 dBm	0.08 V
1790650997	0 Pkt	-64 dBm	0.08 V
1790650281	0 Pkt	-64 dBm	0.08 V
1790649359	0 Pkt	-64 dBm	0.08 V
1790648367	0 Pkt	-64 dBm	0.08 V
1790647445	0 Pkt	-64 dBm	0.08 V
1790646523	0 Pkt	-64 dBm	0.1 V
1790645601	0 Pkt	-64 dBm	0.08 V
1790645149	0 Pkt	-64 dBm	0.08 V
1790644227	0 Pkt	-64 dBm	0.08 V
1790643305	0 Pkt	-64 dBm	0.08 V
1790641606	0 Pkt	-64 dBm	0.08 V
1790641299	0 Pkt	-63 dBm	0.08 V
1790640377	0 Pkt	-65 dBm	0.08 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)