This is the latest recevied telemetry packets stored in our database for station/object XE1CGG-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Value1* | Value2* | Value3* | Value4* | Value5* |
|---|---|---|---|---|---|
| 1836274756 | 134 | 28 | 999 | 378 | 260 |
| 1774129715 | 133 | 29 | 999 | 370 | 247 |
| 1774126162 | 133 | 29 | 999 | 372 | 243 |
| 1774122609 | 134 | 27 | 999 | 381 | 252 |
| 1774119057 | 134 | 26 | 999 | 386 | 261 |
| 1774115504 | 134 | 25 | 999 | 391 | 263 |
| 1774111951 | 134 | 23 | 999 | 396 | 276 |
| 1774108399 | 134 | 23 | 999 | 400 | 274 |
| 1774104846 | 134 | 22 | 999 | 404 | 277 |
| 1774101293 | 134 | 22 | 999 | 404 | 280 |
| 1774097741 | 134 | 22 | 999 | 405 | 277 |
| 1774094188 | 134 | 23 | 999 | 401 | 270 |
| 1774087083 | 134 | 24 | 999 | 395 | 262 |
| 1774083530 | 134 | 25 | 999 | 390 | 269 |
| 1774079978 | 134 | 26 | 999 | 386 | 265 |
| 1774076425 | 134 | 26 | 999 | 383 | 264 |
| 1774072872 | 134 | 27 | 999 | 379 | 257 |
| 1774065767 | 133 | 29 | 999 | 373 | 254 |
| 1774062214 | 133 | 29 | 999 | 370 | 247 |
| 1774055109 | 133 | 31 | 999 | 360 | 231 |
| 1774051556 | 133 | 31 | 999 | 361 | 234 |
| 1774048003 | 133 | 32 | 999 | 355 | 234 |
*Used Equation Coefficients:
Value1: 0, 1, 0
Value2: 0, 1, 0
Value3: 0, 1, 0
Value4: 0, 1, 0
Value5: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)