APRS Track Direct

My position About ☰

reset

YM8KSU-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM8KSU-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1754286599	3 Pkt	-71 dBm	14.05 V
1754285674	1 Pkt	-71 dBm	14.05 V
1754284750	3 Pkt	-71 dBm	14.03 V
1754283824	1 Pkt	-70 dBm	14.03 V
1754282900	3 Pkt	-70 dBm	14.03 V
1754281974	1 Pkt	-70 dBm	14.07 V
1754281050	3 Pkt	-70 dBm	14.05 V
1754280124	1 Pkt	-71 dBm	14.09 V
1754279201	3 Pkt	-70 dBm	14.03 V
1754278275	1 Pkt	-70 dBm	14.05 V
1754277352	3 Pkt	-71 dBm	14.09 V
1754276427	1 Pkt	-71 dBm	14.07 V
1754275504	3 Pkt	-71 dBm	14.05 V
1754274579	1 Pkt	-71 dBm	14.09 V
1754273656	3 Pkt	-70 dBm	14.07 V
1754272732	1 Pkt	-71 dBm	14.09 V
1754271808	4 Pkt	-70 dBm	14.05 V
1754270881	1 Pkt	-71 dBm	14.05 V
1754269956	3 Pkt	-70 dBm	14.05 V
1754269031	1 Pkt	-71 dBm	14.03 V
1754268107	3 Pkt	-71 dBm	14.05 V
1754267181	2 Pkt	-71 dBm	14.09 V
1754266257	3 Pkt	-71 dBm	14.07 V
1754265332	1 Pkt	-71 dBm	14.05 V
1754264409	3 Pkt	-71 dBm	14.05 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)