APRS Track Direct

My position About ☰

reset

BX4AEF-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX4AEF-8. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1753768814	33.1 C	27 p	78 p	1862 p
1753767615	32.6 C	27 p	74 p	1856 p
1753766414	32.1 C	24 p	71 p	1858 p
1753765214	32.9 C	23 p	69 p	1862 p
1753764014	33.1 C	24 p	76 p	1866 p
1753762814	32.3 C	22 p	86 p	1863 p
1753761615	32.6 C	30 p	114 p	1869 p
1753760415	32.6 C	34 p	105 p	1866 p
1753759214	32.6 C	50 p	89 p	1861 p
1753758014	33.2 C	21 p	61 p	1837 p
1753756815	32.2 C	18 p	60 p	1841 p
1753755615	32.2 C	22 p	68 p	1853 p
1753754414	32.5 C	20 p	71 p	1859 p
1753753215	32 C	26 p	75 p	1867 p
1753752014	31.4 C	25 p	97 p	1868 p
1753750815	32.5 C	24 p	144 p	1867 p
1753749614	31.5 C	49 p	152 p	1866 p
1753748415	31.9 C	71 p	128 p	1873 p
1753747215	33.3 C	32 p	80 p	1853 p
1753746015	30.8 C	25 p	69 p	1844 p
1753744815	30.5 C	23 p	70 p	1912 p
1753743615	28.5 C	21 p	80 p	1925 p
1753742415	21.2 C	26 p	87 p	1930 p
1753741215	21.1 C	33 p	92 p	1931 p
1753740015	22.2 C	28 p	80 p	1920 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)