APRS Track Direct

My position About ☰

reset

WA7SWB-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object WA7SWB-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Vin*	Rx1h*	Dg1h*	Eff1h*	A5*
1778048194	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778044594	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778040994	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778037394	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778033794	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778026594	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778022994	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778019394	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778015794	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778012194	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778004995	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1778001395	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777997795	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777994195	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777990595	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777983395	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777979795	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777976195	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777972595	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777968995	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None
1777965396	14.33 Volt	0 Pkt	0 Pkt	0 %	0 None

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)