APRS Track Direct

My position About ☰

reset

HS1AXC-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS1AXC-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1754258268	0 Pkt	-57 dBm	11.71 V
1754256725	0 Pkt	-57 dBm	11.67 V
1754256419	0 Pkt	-57 dBm	11.59 V
1754255797	0 Pkt	-57 dBm	11.63 V
1754255175	0 Pkt	-58 dBm	11.71 V
1754254920	0 Pkt	-58 dBm	11.73 V
1754254298	1 Pkt	-57 dBm	11.69 V
1754252946	0 Pkt	-57 dBm	11.69 V
1754252241	0 Pkt	-57 dBm	11.57 V
1754251619	0 Pkt	-57 dBm	11.73 V
1754250997	0 Pkt	-57 dBm	11.71 V
1754250375	0 Pkt	-57 dBm	11.73 V
1754249800	0 Pkt	-57 dBm	11.53 V
1754249178	0 Pkt	-57 dBm	11.69 V
1754248556	0 Pkt	-58 dBm	11.53 V
1754248089	0 Pkt	-57 dBm	11.69 V
1754247156	0 Pkt	-58 dBm	11.71 V
1754246609	0 Pkt	-57 dBm	11.71 V
1754245987	0 Pkt	-57 dBm	11.57 V
1754245365	0 Pkt	-58 dBm	11.61 V
1754245229	0 Pkt	-57 dBm	11.71 V
1754244607	0 Pkt	-57 dBm	11.61 V
1754243985	0 Pkt	-57 dBm	11.53 V
1754243363	0 Pkt	-57 dBm	11.53 V
1754242741	0 Pkt	-57 dBm	11.73 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)