APRS Track Direct

My position About ☰

reset

W4IJG-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W4IJG-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Batt_V*	Uptime*	Cap_Rem*
1754134891	13.3 Volts	205 Hrs	99 %
1754134293	13.2 Volts	205 Hrs	97 %
1754133691	13.3 Volts	205 Hrs	99 %
1754133090	13.3 Volts	205 Hrs	99 %
1754132491	13.3 Volts	205 Hrs	99 %
1754131889	13.3 Volts	205 Hrs	99 %
1754131288	13.2 Volts	204 Hrs	97 %
1754130688	13.3 Volts	204 Hrs	99 %
1754130087	13.2 Volts	204 Hrs	97 %
1754129486	13.3 Volts	204 Hrs	99 %
1754128886	13.2 Volts	204 Hrs	97 %
1754128285	13.3 Volts	204 Hrs	99 %
1754127685	13.2 Volts	203 Hrs	97 %
1754127085	13.2 Volts	203 Hrs	97 %
1754126484	13.2 Volts	203 Hrs	97 %
1754125884	13.2 Volts	203 Hrs	97 %
1754125284	13.3 Volts	203 Hrs	99 %
1754124085	13.3 Volts	202 Hrs	99 %
1754123484	13.3 Volts	202 Hrs	99 %
1754122881	13.2 Volts	202 Hrs	97 %
1754122280	13.3 Volts	202 Hrs	99 %
1754121680	13.3 Volts	202 Hrs	99 %
1754121079	13.3 Volts	202 Hrs	99 %
1754120478	13.3 Volts	201 Hrs	99 %
1754119878	13.3 Volts	201 Hrs	99 %

*Used Equation Coefficients:

Batt_V: 0, 0.1, 0

Charg_A: 0, 0.1, 0

Uptime: 0, 1, 0

Cap_Rem: 0, 1, 0

Tim_10%: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)