APRS Track Direct

My position About ☰

reset

YM4KBO Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM4KBO. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1836274536	3 Pkt	-67 dBm	0 V
1836274409	5 Pkt	-67 dBm	0 V
1836273914	4 Pkt	-67 dBm	0 V
1762278384	4 Pkt	-75 dBm	0.02 V
1762277761	1 Pkt	-73 dBm	0.06 V
1762277139	3 Pkt	-74 dBm	0.02 V
1762276517	5 Pkt	-74 dBm	0.06 V
1762275894	1 Pkt	-74 dBm	0.02 V
1762275272	4 Pkt	-74 dBm	0 V
1762274649	5 Pkt	-74 dBm	0.04 V
1762274026	1 Pkt	-73 dBm	0 V
1762273404	3 Pkt	-73 dBm	0 V
1762272782	4 Pkt	-74 dBm	0.02 V
1762272160	2 Pkt	-74 dBm	0.02 V
1762271538	4 Pkt	-75 dBm	0.02 V
1762270915	3 Pkt	-74 dBm	0 V
1762270293	4 Pkt	-74 dBm	0 V
1762269671	5 Pkt	-74 dBm	0.02 V
1762269048	6 Pkt	-74 dBm	0 V
1762268425	1 Pkt	-75 dBm	0.04 V
1762268311	8 Pkt	-71 dBm	0.02 V
1762267688	5 Pkt	-71 dBm	0 V
1762267066	8 Pkt	-71 dBm	0.06 V
1762266442	4 Pkt	-70 dBm	0 V
1762265820	2 Pkt	-70 dBm	0.04 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)