APRS Track Direct

My position About ☰

reset

BM6HML-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HML-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1790661231	41.4 C	6 p	19 p	502 p
1790660031	40.3 C	6 p	21 p	499 p
1790658832	42.6 C	7 p	23 p	504 p
1790657631	40.1 C	8 p	24 p	509 p
1790656431	41.3 C	8 p	24 p	510 p
1790655231	40.6 C	8 p	22 p	511 p
1790654031	42 C	8 p	23 p	513 p
1790652832	40.6 C	6 p	25 p	513 p
1790651631	40.9 C	9 p	27 p	516 p
1790650431	39.2 C	10 p	26 p	516 p
1790649231	40.8 C	8 p	25 p	515 p
1790648031	38.9 C	8 p	26 p	514 p
1790646831	40.3 C	9 p	29 p	518 p
1790645631	41.3 C	9 p	32 p	518 p
1790644431	40 C	11 p	33 p	516 p
1790643231	40 C	12 p	26 p	513 p
1790642031	40.3 C	10 p	24 p	513 p
1790640831	40.8 C	4 p	23 p	515 p
1790639631	40.9 C	10 p	22 p	523 p
1790638432	41.5 C	9 p	18 p	521 p
1790637231	41 C	3 p	17 p	522 p
1790636031	41.2 C	6 p	23 p	529 p
1790634831	39.6 C	8 p	28 p	535 p
1790633632	41.2 C	9 p	30 p	538 p
1790632431	39 C	11 p	31 p	541 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)