APRS Track Direct

My position About ☰

reset

K8VAN-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K8VAN-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1749309683	13.88 Volt	330 Pkt	100 Pkt	58 Pcnt
1749309084	13.88 Volt	250 Pkt	60 Pkt	57 Pcnt
1749307282	13.88 Volt	240 Pkt	40 Pkt	62 Pcnt
1749306684	13.88 Volt	260 Pkt	60 Pkt	61 Pcnt
1749303681	13.88 Volt	370 Pkt	120 Pkt	53 Pcnt
1749303082	13.88 Volt	380 Pkt	120 Pkt	53 Pcnt
1749302481	13.88 Volt	450 Pkt	160 Pkt	53 Pcnt
1749301282	13.88 Volt	440 Pkt	130 Pkt	53 Pcnt
1749300681	13.88 Volt	390 Pkt	110 Pkt	53 Pcnt
1749300082	13.88 Volt	400 Pkt	110 Pkt	53 Pcnt
1749299482	13.88 Volt	380 Pkt	110 Pkt	52 Pcnt
1749298881	13.88 Volt	300 Pkt	70 Pkt	48 Pcnt
1749298282	13.73 Volt	250 Pkt	50 Pkt	45 Pcnt
1749297683	13.88 Volt	250 Pkt	50 Pkt	46 Pcnt
1749297083	13.88 Volt	230 Pkt	50 Pkt	44 Pcnt
1749295881	13.88 Volt	210 Pkt	30 Pkt	43 Pcnt
1749295281	13.88 Volt	220 Pkt	30 Pkt	44 Pcnt
1749294681	13.88 Volt	210 Pkt	30 Pkt	44 Pcnt
1749293486	13.88 Volt	210 Pkt	20 Pkt	41 Pcnt
1749292883	13.88 Volt	200 Pkt	30 Pkt	41 Pcnt
1749292283	13.88 Volt	210 Pkt	30 Pkt	41 Pcnt
1749291682	13.88 Volt	230 Pkt	40 Pkt	43 Pcnt
1749291083	13.88 Volt	230 Pkt	30 Pkt	43 Pcnt
1749290482	13.95 Volt	220 Pkt	30 Pkt	44 Pcnt
1749289883	13.88 Volt	220 Pkt	30 Pkt	46 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

I1: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)