APRS Track Direct

My position About ☰

reset

K4KSC-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K4KSC-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1790651176	53.2 V	-0.6 A	88 %	0 W	16 W
1790650577	53.2 V	-0.8 A	88 %	0 W	17 W
1790648783	53.2 V	-0.7 A	89 %	0 W	17 W
1790648186	53.2 V	-0.8 A	89 %	0 W	17 W
1790646977	53.2 V	-0.6 A	90 %	0 W	17 W
1790645783	53.2 V	-0.7 A	90 %	0 W	17 W
1790643377	53.2 V	-0.6 A	91 %	0 W	16 W
1790642784	53.2 V	-0.8 A	92 %	0 W	16 W
1790642176	53.2 V	-0.9 A	92 %	0 W	17 W
1790641578	53.2 V	-0.6 A	92 %	0 W	16 W
1790640977	53.2 V	-0.6 A	92 %	0 W	17 W
1790639777	53.2 V	-0.6 A	93 %	0 W	17 W
1790639183	53.2 V	-0.7 A	93 %	0 W	17 W
1790637977	53.2 V	-0.6 A	94 %	0 W	18 W
1790637380	53.2 V	-0.6 A	94 %	0 W	17 W
1790636777	53.2 V	-0.7 A	94 %	0 W	17 W
1790635588	53.3 V	-0.2 A	95 %	18 W	17 W
1790634982	53.3 V	-0.1 A	95 %	19 W	17 W
1790634375	53.3 V	-0.2 A	95 %	19 W	17 W
1790633175	53.3 V	0 A	95 %	45 W	16 W
1790632577	53.3 V	0 A	95 %	45 W	17 W
1790631975	53.3 V	0.2 A	96 %	70 W	16 W
1790630776	53.3 V	0 A	96 %	47 W	17 W
1790629575	53.3 V	0.1 A	96 %	72 W	16 W
1790628976	53.3 V	0 A	96 %	48 W	16 W

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)