APRS Track Direct

My position About ☰

reset

SR9POD Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9POD. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	T_in*	Rx1h*	Dg1h*
1786728178	13.65 Volt	32 C	290 Pkt	30 Pkt
1786727578	13.65 Volt	32.5 C	270 Pkt	30 Pkt
1786726976	13.73 Volt	32.5 C	270 Pkt	30 Pkt
1786725178	13.65 Volt	33 C	240 Pkt	20 Pkt
1786724578	13.73 Volt	33.5 C	250 Pkt	20 Pkt
1786722778	13.73 Volt	33.5 C	260 Pkt	20 Pkt
1786722178	13.73 Volt	33.5 C	240 Pkt	10 Pkt
1786721578	13.73 Volt	34 C	230 Pkt	10 Pkt
1786720979	13.73 Volt	34 C	220 Pkt	10 Pkt
1786718578	13.73 Volt	34 C	240 Pkt	10 Pkt
1786717377	13.73 Volt	34 C	250 Pkt	10 Pkt
1786716778	13.73 Volt	34 C	250 Pkt	10 Pkt
1786716178	13.73 Volt	34 C	260 Pkt	20 Pkt
1786713778	13.73 Volt	34 C	220 Pkt	30 Pkt
1786711378	13.73 Volt	34 C	220 Pkt	10 Pkt
1786710179	13.73 Volt	34.5 C	200 Pkt	10 Pkt
1786709578	13.73 Volt	34.5 C	190 Pkt	10 Pkt
1786707179	13.73 Volt	35 C	310 Pkt	70 Pkt
1786706579	13.73 Volt	34.5 C	350 Pkt	90 Pkt
1786705975	13.73 Volt	34.5 C	380 Pkt	90 Pkt
1786705378	13.73 Volt	34 C	350 Pkt	70 Pkt
1786703575	13.73 Volt	34.5 C	470 Pkt	100 Pkt
1786702979	13.65 Volt	34 C	520 Pkt	90 Pkt
1786702375	13.73 Volt	34 C	560 Pkt	90 Pkt
1786701181	13.65 Volt	33.5 C	470 Pkt	50 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

T_in: 0, 0.5, -64

T_out: 0, 1, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)