APRS Track Direct

My position About ☰

reset

BX6ABV-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6ABV-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1786725281	35.6 C	3 p	15 p	742 p
1786724081	39.6 C	6 p	18 p	744 p
1786722880	38.9 C	6 p	18 p	744 p
1786721680	38.8 C	6 p	18 p	744 p
1786720480	38.8 C	6 p	18 p	745 p
1786719280	38.8 C	6 p	18 p	745 p
1786718080	44.6 C	6 p	18 p	745 p
1786716880	43.6 C	6 p	18 p	745 p
1786715680	40.9 C	6 p	18 p	745 p
1786714481	44.5 C	6 p	18 p	745 p
1786713280	45.1 C	6 p	18 p	745 p
1786712080	44 C	6 p	24 p	745 p
1786710880	45.1 C	6 p	26 p	745 p
1786709680	43.7 C	12 p	26 p	745 p
1786708480	44.5 C	8 p	20 p	739 p
1786707280	44.1 C	6 p	18 p	737 p
1786706081	38.6 C	6 p	18 p	737 p
1786704880	38.2 C	6 p	18 p	737 p
1786703680	39.1 C	6 p	18 p	737 p
1786702480	39.1 C	6 p	18 p	739 p
1786701280	39.5 C	6 p	19 p	748 p
1786700080	40.3 C	6 p	22 p	749 p
1786698880	45.4 C	7 p	24 p	750 p
1786697680	44 C	9 p	25 p	750 p
1786696480	41.4 C	8 p	26 p	749 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)